ECHO chainsaw oilers may stop working for several reasons. When this happens, it’s unsafe to keep using your chainsaw. The good news is, however, that you can fix it!
To fix the oiler on your ECHO chainsaw, clean the bar plate, the guide bar, and the inlet and outlet ports. You may also need to unclog the oil filter, change faulty oil pumps, fill up the oil tank or increase the oil output.
This article will cover these points in greater detail. However, before you consider fixing your ECHO chainsaw yourself, you should learn how to tell when the oiler is faulty. Therefore, make sure to keep reading until the end of this article.
Signs of ECHO Chainsaw Oiler Malfunction
Your chainsaw will start to show various symptoms that suggest it’s no longer receiving oil. Dry chainsaws, overheating, and diminished efficiency are warning indicators.
Your Chainsaw Is Dry
One typical sign of a bad oiler is a dry chainsaw. A chainsaw that is dry indicates that it needs oil. After running your chain for a minute or two, oil should normally be on it.
However, if you run it and touch the chain afterward and there is no oil, the chain is not getting oil. Either the oiler is malfunctioning, or the lubricant has run out.
Your Chainsaw Overheats
The system will overheat if the chainsaw runs out of oil or if something stops the oil from reaching the chain. Your chainsaw will suddenly get very hot and smoky. If you keep using it, it’ll become too hot to touch. It can damage the chainsaw if you don’t fix this (source).
Your Chainsaw Loses Effectiveness
The ECHO chainsaw is powerful at full strength. However, when the chainsaw isn’t running as it should, the oiler may have a problem. The dryer the chainsaw gets, the less effective it will become because the oil provides friction that enables it to function effectively.
7 Ways To Fix an Echo Chainsaw Oiler
You can fix a malfunctioning Echo chainsaw. Let’s take a look at 7 ways.
1. Clean Any Dirt or Sawdust Under the Bar Plate
Remove and clean out any dirt and sawdust under the bar plate so the oil can pass freely to the chainsaw when in use.
Dirt and sawdust particles get stuck under the bar plate as you use the ECHO chainsaw. Over time, they can block the flow of oil to the chainsaw.
This is because the oil lubricates the chainsaw as it passes through the plate from the oil outlet. Therefore, the oil won’t flow freely if this passage is obstructed by dirt and sawdust. Holding the throttle should cause the bar oil to spill once the plate has been cleaned.
2. Fill Up the Oil Tank
The oil tank is the first place to look. If your oil tank is empty, It won’t lubricate your chainsaw. So, before doing anything more, you should see if there is still any oil in the tank or if the level has significantly dropped.
If so, refuel the engine by adding oil. Test the chainsaw after completing this; it should function properly.
3. Clean the Oil Inlet and Outlet Ports
Check the ports for clogs if the oil won’t come out after you’ve cleaned the plate and refilled it. Here’s a step-by-step process.
- First, detach the chainsaw from its body.
- Then pour out any oil in the oil tank into the oil container.
- Next, remove the bar plate.
- You’ll find the oil inlet and outlet. Use a sick, small screwdriver or whatever can get in there to clean it out properly.
- Pour the oil again into the oil tank.
- Fix the bar plate.
- Reattach the chainsaw.
Before you attach the chainsaw and bar plate, turn on the chainsaw to check if the oil comes out.
4. Check the Filter
The oil passes through a filter in the oil tank before it comes out. It will be difficult for the oil to pass through if this filter is clogged.
Drain the oil tank, then check the filter. Clear it before reinstalling it and adding oil to the tank if it’s clogged.
5. Replace Faulty Oil Pump
If everything checks out following your inspection, the oil pump can be the source of the issue. Changing a malfunctioning oil pump requires professional help. You can always find a repair service nearby. However, make sure to ask around for recommendations or read online reviews. That way, you’ll be able to make a well-informed decision.
6. Clean Clogged Guide Bar
Clogs in the guide bar may also prevent oil from reaching your chainsaw. Here’s how to clear it:
- Detach the chain and bar.
- Clean the oil hole on the bar.
- Use any sharp tool to get into the groove and clear out any dirt there.
- Fix it back again and try it out (source).
7. Increase Oil Output
A minimum volume of oil is necessary for the chainsaw to operate properly. If it receives anything less, it won’t be able to work properly.
If your chainsaw isn’t getting oil, look at the oiling control. There are plus and minus signs on the controls. Turn the knob to the plus side to increase oil output.
Once you’ve finished, position a wood log over the chainsaw and turn it on. If it releases oil, then it’s all good (source).
Echo Chainsaw Maintenance Tips
Adequate maintenance will reduce the frequency of repairs and extend the chainsaw’s lifespan. Here are some maintenance tips.
- Check the chain and bar lubrication before any use.
- Fill the tank before use.
- Don’t empty the oil tank. It should have a little oil at the end of every use.
- A chainsaw should be turned on, on the ground.
- Use the recommended oil for your chainsaw.
- Allow it to run for a few seconds so it can come up to heat before using it.
- Check the fuel filter for debris, and remove, if any.
- Clean your fuel tank monthly to remove old fuel stuck to the body.
- Check for loose parts or screws and tighten them.
- Keep an eye on the chainsaw’s safety features, like the chain brake and throttle. Ensure they are not faulty. If they are, change it before use (source).
Has your Echo chainsaw chain ever come loose? What can you do when that happens? Check out my guide to learn how to fix it.
Conclusion
If your echo chainsaw doesn’t have enough oil to lubricate it, it won’t work properly. Ensure the oil tank in your chainsaw has sufficient oil before operating the device.
If there’s sufficient oil, but the chainsaw isn’t well lubricated, clean the oil filter. Clogs can prevent the smooth passage of oil. Sometimes, the problem may be a faulty oil pump, which you’ll need to replace.